Doors

Doors & Drawer Fronts

In this section you will choose the door style you want on your cabinets in this job. Cabinet Solutions allows you a lot of flexibility in placing doors. You can place a different door styles on upper cabinets than on base cabinets and different styles on drawers. Later in this manual you will learn how to change the door style of any cabinet within a room or even change the door style of one particular opening in a cabinet. The door standard section allows you to enter the standards that control the production of the cut list for the door parts. Even if you do not build your own doors, you may want to set the sizes to the approximate size that your door company uses so your pictures will most closely represent what the customer will actually be getting.

To select a door style:

Click on the button in standards labeled Doors + Drawer Fronts.
In the window that opens, choose between Upper Doors, Base Doors or Drawer Fronts.
Click on the "Basic Door Style" you want for the cabinets. The styles are as follows:

slab door with vertical grain
slab door with horizontal grain
square frame door
square frame miter door
square frame door with simple top arch
square frame door with simple top & bottom arch
square frame door with cathedral top arch
square frame door with cathedral top & bottom arch

Select the "Panel Style" if you are using any of the frame doors:

glass (including mirrors)
raised
recessed
frame only (no panels)
one-piece recessed back (also called a back panel door)

Note: If you selected to use a "slab door" a check box and an entry field will appear that allow you to choose to use edging on the doors and to give that edging a thickness.

Center Rail

Earlier you set a standard to add a center rail when a door gets to a certain size. This section will control how that added center rail will be cut. You may be arching your top or bottom rail. Do you want an arch cut in the center rail? Do you want it arched for the bottom panel only or both the top and bottom panels?

No Arches: This option will always put a straight center rail in your doors.
Arch Top Edge Only: This option will cut an arch in the top side of the center rail.
Arch Bottom Edge Only: This option will cut an arch in the bottom side of the center rail.
Arch Top and Bottom Edges: This option will cut an arch in the top and bottom side of the center rail.

Knobs / Pulls

You can customize the placement of knobs or pulls in Job Standards for your Upper Doors, Base Doors, and Drawer Fronts. You can even customize each individual opening's knob or pull placement through Openings / Rollouts.

Choose Hardware:

None: Click this radio button if you will not be using any knobs or pulls for this door.
Knobs: Click this radio button if you will be using knobs for this door.
Pulls: Click this radio button if you will be using pulls for this door.

Choose Placement:

Center of Door: Click this radio button if you would like the knob or pull to be centered on the door. This is useful for drawer-fronts, etc.
Top of Stile: Click this radio button if you would like the knob or pull to be placed at the top of the stile. If you are doing European construction, the knob or pull will be placed at the top edge of the door.
Middle of Stile: Click this radio button if you would like the knob or pull to be placed in the middle of the stile (vertically). If you are doing European construction, the knob or pull will be placed in the middle edge (vertically) of the door.
Bottom of Stile: Click this radio button if you would like the knob or pull to be placed at the bottom of the stile. If you are doing European construction, the knob or pull will be placed at the bottom edge of the door.
Add Knob/Pull When Door Width Is >: If you would like an extra knob or pull added when the door's width is greater than a certain amount, then enter that width here. The knobs or pulls will be positioned proportionally to the edge of the door. This is useful for drawer-fronts that need two knobs or pulls. (If you would not like an additional knob or pull added then make the amount very large so that the width would never exceed that amount.)

Position Offset: This section allows you to set the position of the door pull or knob on the door itself when Slab style doors are selected. Please note this doesn't get displayed if the Placement is set to center of door.

Note: Arch Depth is set in the Doors - Shaper Knife Setup window below. Wainscot Standards

Doors - Shaper Knife Setup Window:

Arch Depth: Enter the depth you cut into your top rail if you are using a door stile that has an arched top here.
Panel Size Less: Enter the amount you want to subtract off your panels to allow for expansion and contraction here.
Groove Depth: Enter the depth you cut the groove in your stiles and rails to receive the panel here. You may refer to this cut as a "cope" depth.
Amount Trimmed-Off with Groove: Enter the amount you will trim off your stiles / rails when you run your groove for your panel.
Amount Trimmed-Off with Edge Detail: Enter the amount you will trim off your stiles rails when you run your edge detail on your doors.

Doors - Wainscot Standards Window:

"French Lites or Wainscot" is a term used to describe the divisions of the door panel. This is most commonly used with glass doors but in Cabinet Solutions you can divide wood panels also. Check the box if you want to divide your panel. Use the radio buttons below to set these divisions as structural (where you will have multiple panels within the door) or non-structural (which will just give you a single panel with decorative mullions over the top).

Set wainscot if you wish divide the door into wainscot panels. Set the number of panels or lites to use in the edit field below in the dialog window.

The following 4 standards for left & right stile and top & bottom rail widths should be given finished sizes. If you cut these pieces oversize and then trim small amounts off when the panel groove is cut and the edge detail is put on, there will be other standards to use to enter that information so your cut-list is correct.

Left Stile Width: Enter the finished width of the left stile.
Right Stile Width: Enter the finished width of the right stile.
Top Rail Width: Enter the finished width of the top rail.
Bottom Rail Width: Enter the finished width of the bottom rail.
Center Rail Width: Enter the width you want the center rails to be when the program adds them here.
French Lite Center Rail Width: Enter the width you want the center rails (horizontal face frame piece) to be when you are adding "French Lites".
French Lite Mullion Width: Enter the width you want the mullions (vertical frame piece) to be when you are adding "French Lites".
French Lite Thickness: Enter the thickness of the French Lite parts.

Wainscot ONLY Shaper Knife Settings

Panel Size Less: Enter the amount you want to subtract off your panels to allow for expansion and contraction here.
Groove Depth: Enter the depth you cut the groove in your stiles and rails to receive the panel here. You may refer to this cut as a "cope" depth.
Amount Trimmed-Off with Groove: Enter the amount you will trim off your stiles / rails when you run your groove for your panel.
Amount Trimmed-Off with Edge Detail: Enter the amount you will trim off your stiles rails when you run your edge detail on your doors.